FADU Parts & Accessories
| FADU REPLACEMENT PARTS | |||
|---|---|---|---|
| Photo | Item No. | Description | Price |
 |
SGB-01 | Strain-Gauged Bolt, Replacement (ea) | $695 |
 |
CSGB-01 | Cable, Strain-Gauged Bolting, Replacement (ea) | $195 |
 |
LC-01 | Load Cell (w/ trade-in of old load cell, w/o trade-in) | $895/$950 |
 |
GCS-01 | Gasket Compression Sensor (w/ trade-in of old sensor, w/o trade-in) | $325/$380 |
 |
DL-01 | Draw Latch, 304 Stainless Steel, Adjustable, Load-rated @ 800 lbs | $55 |
| (No photo) | CPC-01 | Compartmented Small Parts Case, Plastic, w/ cam-locks | $15 |
| (No photo) | OCSID-01 | FADU Control Software Installation Disk, Replacement | $75 |
 |
BASE-EC-01 | End Cap, Storage, Base Unit | $95 |
 |
BASE-EC-02 | End Cap, Standoff, Base Unit | $75 |
 |
BASE-CT-01 | Computer Tray, Lift-Out | $195 |
| (No photo) | BASE-LRH-01 | Handle, Lifting, Load-Rated, Spring-Loaded (ea) | $35 |
 |
NR_01 | Nut Retainer, w/ Solid Bottom | $125 |
 |
PSC-01 | Strain-Gauged Bolt Protective Shroud Cover, Anodized Aluminum, with Bolt Numbering for Standard 4"-Class 150 flange (-01) or Class 300 flange (-02) | $275 |
 |
CCR-01 | Cable, Inner Controller Ring, PVC (See image) | $5 |
| CONSUMABLE ITEMS | |||
 |
TS4-01 | A193 B7 Threaded Studs for Torque-Preload Module (set of 5) | $20 |
 |
FSP-01 | Flange Simulation Plates (set of 4) | $55 |
| FADU ACCESSORIES | |||
| TPT-01 | Torquing Pattern Template, Cross-Pattern | $25 | |
| TPT-02 | Torquing Pattern Template, Right-Hand Progression | $25 | |
| TPT-03 | Torquing Pattern Template, 4-Bolt Pattern | $25 | |
| TPT-00 | Torquing Pattern Template, Set of All Three | $65 | |
 |
1/2" Drive Torque Wrench, Digital, 20-250 ft.-lbs. Equipped to down-load individual torque values or store values in memory which can be directly down-loaded to a printer/computer or datalogger via RS232. Selectable Modes of Operation "Peak Hold" and "Track" modes of operation are standard. Eectronics are far superior to competitors in capturing real torque value in "Peak" mode . Easy Set-Up Target torque values (high and low percentage, +/- tolerances and torque engineering units) are easily programmed through the keypad and shown on the LCD. Quality Construction Proven industrial quality. Designed for continuous use. Batteries A 9V alkaline battery is standard and provides enough power for 60 hours of operation. A "LO BAT" indication on the display signals for replacement. Accuracy +/- 1% From 20-100% of scale +/- 1%, plus 5 increments, from 10 -20% of scale. Baud Rate The baud rate for downloading to a printer/computer/data logger is selectable. The factory set rate is 1200. Options are 300, 600, 1200 2400, 4800, 9600 or 19,200. Cables: P113 - 50 - TO 9 PIN PC P113-60 - TO 25 PIN PC. Audio/Visual Indicators. Wrenches are equipped with both audio and visual signals in addition to the torque information supplied on the LCD. Audio Signal: An audio signal is emitted when the minimum acceptable standard indicators of high and low preset torque value is reached or the upper torque limit is exceeded. Visual Indicators: Bright green and red LED's are standard indicators of high and low preset torque limits. Over-Load Protection: The red LED flashes, the audio buzzer sounds and "OVER" is displayed on the LCD when the torque range of the wrench is exceeded. | Price Upon Request | |
| 539-P113-50 | CABLE, COMPUTORQ II TO 9-PIN PC | Price Upon Request | |
 |
500-196-20 | Caliper, digital, 0-6" range, for pre-measuring gaskets. Shows your measurement on a large LCD display. Inch/Metric button lets you switch the readout between standard and metric instantly. This digital caliper allows you to "zero" the readout. In addition, the Zero/ABS button lets you display the absolute coordinate or true position from the origin point (which is usually the jaw-closed point). You can perform four types of measurement with this caliper: outer diameter, inner diameter, depth and step. (With step measurement, the butt end of the fixed jaw is used for one end of the measurement, allowing you to measure upper/lower or inner/outer "steps" in a work piece.) The internal memory keeps your last measurement, even when the instrument is turned off. Placed for convenient thumb access, the jaw wheel lets you open and close the jaw and make fine adjustments. This digital caliper is a lightweight instrument made with durable hardened stainless steel. Accuracy is 1/1000th of an inch (plus or minus), and the readout shows your measurements down to 0.0005" / 0.01mm increments. A convenient fitted plastic storage case is included. Battery life is 3.5 years of normal use. |
Price Upon Request |
 |
Laptop | Factory-reconditioned Lenovo (IBM) or Dell laptop pre-installed with 64-bit operating system and FADU control software. (Exact laptop specifications will vary with availability) | $900 |